Swivel Mount - Rotating stainless steel anchor for wall and ceiling

• The anchor point that moves with you: 360° rotating shackle follows every exercise - no twisted straps, no fixed pulling direction.
• Complete stainless steel system: base plate, swivel, shackle and expansion anchors - built to shrug off sweat, moisture and time.
• Plate and shackle tested to 1300 kg (2866 lbs) - a huge safety margin over anything a workout will ask of them.
• Low-maintenance stainless steel plain bearing: clean when needed and care for it with a little PTFE spray oil.
• Solid 8 mm (0.3 in) base plate with 90 mm (3.5 in) diameter - compact footprint, maximum strength.
• Clip a carabiner directly into the shackle or attach our anchor sling.
• 4 stainless steel expansion anchors for unbroken concrete included.
• Successor of the proven aeroSling Mount - now with a moving eyelet instead of a fixed one.
• Includes 1 Swivel Mount, 4 expansion anchors and mounting instructions.

Your training moves - now your anchor point does too

A fixed eyelet forces every strap and rope into one direction and slowly twists them with every rep. The aerobis Swivel Mount ends that: its shackle sits on a freely rotating stainless steel swivel, so the anchor point follows your movement instead of fighting it. Rows, flys, rotational work, single-arm exercises - the Mount always faces the right way.

Massively overbuilt - on purpose

The Swivel Mount is machined entirely from stainless steel: an 8 mm (0.3 in) thick base plate with 90 mm (3.5 in) diameter, a solid swivel pin and a heavy-duty bow shackle. Plate and shackle are tested to a load of 1300 kg (2866 lbs) - far beyond anything a workout will ever throw at them. That margin is your safety reserve for dynamic, explosive training.

Low-maintenance plain bearing

The Swivel Mount rotates on a low-maintenance stainless steel plain bearing, a design chosen deliberately for years of heavy use in home gyms, studios and outdoor setups. Keep the gap between base plate and pin clean and, when needed, care for it with a little PTFE spray oil: see the care note below.

One mount, all your training tools

Clip a carabiner straight into the shackle for the fastest possible setup, or girth hitch our anchor sling through it for slings, ropes and Powerbands. Mounted on the ceiling it carries your aeroSling; on the wall it anchors rope trainers, resistance bands and more - at exactly the height you want.

Made to be seen

Polished stainless steel, a clean circular plate and no plastic anywhere: the Swivel Mount looks like a piece of hardware you want on your wall, not something you hide behind the door. Even without equipment attached it sits flush and elegant in any room.

⚠️ What the load rating means

The 1300 kg (2866 lbs) figure describes the tested strength of the base plate and the shackle - it is not a promise about your wall. In practice, the substrate and the anchoring set the real limit: a mount is only ever as strong as the concrete it sits in. Use the supplied anchors in solid, unbroken concrete only, and have your substrate assessed by a specialist if you are unsure. Not intended for securing people.

Care your Swivel Mount

If your Swivel Mount turns stiffly: remove carabiner, sling and bands, wipe the gap between base plate and pin, spray a little PTFE spray oil into it, turn the pin once and wipe off the excess. Keep slings and bands oil-free. Outdoors, in wet conditions or with a lot of sweat, check more often and respray.

Measurements

Base plate diameter: 90 mm (3.5 in)
Base plate thickness: 8 mm (0.3 in)
Tested load (plate and shackle): 1300 kg (2866 lbs)
Weight: 400 g (0.9 lbs) mount + 200 g (0.4 lbs) anchors = 600 g (1.3 lbs) total
Material: stainless steel (mount and anchors)